Canon PIXMA IP1800 overview

Number of problems: 19

Number of solved problems: 5

Number of unsolved problems: 14

Problem resolution: 26%

Compared to other printers:

Canon PIXMA IP1800: Likelihood of getting a solution

Good 
Ranking: 83rd out of 413
Most likely to get a solution:
Canon PIXMA 210 - problem resolution score of 100%
Least likely to get a solution:
Brother DCP330C - 0 out of 19 problems solved
Common problems with the Canon PIXMA IP1800


Solutions for the Canon PIXMA IP1800
1 person also had this problem.

Problem: Waste Ink Tank Almost Full

There are 0 comments on this problem.

Solution 1: You can reset the waste ink tank counter yourself. Be aware that this doesn't actually empty the waste ink tank itself (a little felt pad deep inside your printer), but it does allow you to continue printing.

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice, then release all buttons
5: When the indicator lights steady, press RESUME three or four times. The indicator should be orange.
6: Press Power to set data

To actually drain the waste ink tank, you'll need to take your printer to pieces and find, clean, wash and dry the felt pads found in the base of the printer. This is a complicated procedure, but it is a good idea to do it if you're technically minded. Many people have just reset the code without actually draining the pads and very few have run into problems as a result. If you do this, you risk damaging your printer and/or the surface it sits on if the pads absorb too much ink. However, if you're going to buy a new printer anyway, you might just reset the code and stand it on a piece of paper or card. It's up to you, just understand the risks.

1 out of 1 person found this solution helpful.
Was this solution helpful?
There are 0 comments on this solution.

Post comments, submit alternative solutions or receive notifications



0 people also had this problem.

Problem: Prints are coming out too dark

There are 0 comments on this problem.

Solution 1: This is a common issue that is largely down to personal taste. The only real way to improve (i.e. lighten) your prints is to first lighten them using a piece of photo editing software. A good choice would be Adobe Photoshop elements, but there are free alternatives. Do a google search for "Free Photo Editing Software" (there should be a google search box on this page near the top).
0 out of 0 people found this solution helpful.
Was this solution helpful?
There are 0 comments on this solution.

Post comments, submit alternative solutions or receive notifications



0 people also had this problem.

Problem: Very low print quality

There are 0 comments on this problem.

Solution 1: There are a number of steps you can take to solve this problem (in order of easiest & least expensive first).

1. Make sure you have tried printing a nozzle check and you've carried out all the maintenance tasks that the manual alows (align print head, clean print head etc).
2. Your cartridge may be faulty. Ink cartridges that use non-genuine ink are of variable quality and you use them at your own risk. Even genuine cartridges can expire if used after the expiry date. Bad ink can clog your nozzle. It may be that you have a dried-out ink cartridge - try another one if you have one handy.
3. The print head may need cleaning. There are Canon print head cleaning kits available (use Google top right) or you could try doing this yourself - some people have had success immersing the print head (not the cartridge) in cleaning alcohol, warm water or using compressed air to gently blow through the nozzles.
4. Buy a new print head. Check the prices before you do this as (a) you may be throwing good money after bad, and (b) the price of a new printer may be the same as a new print head. Again, use Google (top right of this page) to search for these if you wish.
0 out of 0 people found this solution helpful.
Was this solution helpful?
There are 0 comments on this solution.

Post comments, submit alternative solutions or receive notifications



0 people also had this problem.

Problem: Genuine original Canon vs Compatible & Refill Cartridges - which should I use?

There are 0 comments on this problem.

Solution 1: It really is up to you. There are many people who swear by refills and compatible cartridges, and many others who have had problems with them. In a nutshell:

Dangers: Compatible/refilled cartridges vary in ink quality. Poor quality ink can dry out your print head and cause damage. You can replace your print head, but this can cost as much as a new printer. You will also invalidate your warranty by using non-genuine ink.

Benefits: Canon ink is very expensive and good quality compatible substitutes can severely cut the cost of printing without damaging your printer.

Minimise the risks - you can take the following steps to minimise the risks of damaging your printer (it's a good idea to follow this advice whether you use genuine cartridges or not):

- Try not to let your cartridges run dry - this can clog the print head.
- Always power off the printer using the printer's power switch rather than simply unplugging and switching off at the mains. The reason is that some printers keep the ink in a ready (i.e. open) state when they are printing to keep printing time shorter. When you power off the printer, it closes the ink cover, keeping the ink tanks sealed. If you just unplug the unit, it will not cover the print head and leave it exposed. For this reason, you should restart your printer and shut it down again if you experience a power cut while the unit is on.
0 out of 0 people found this solution helpful.
Was this solution helpful?
There are 0 comments on this solution.

Post comments, submit alternative solutions or receive notifications



2 people also had this problem.

Problem: I cannot print as the paper will not feed through, I cannot see any paper stuck in the printer and cannot remember having to pull anything through but when I try to print the paper gets scrunched on the right hand corner (facing the machine) before feeding through, any suggestions? thanks Jenny

There are 0 comments on this problem.

Solution 1: Jenny: I am having the exact SAME issue! Someone please help!
0 out of 1 person found this solution helpful.
Was this solution helpful?
There are 0 comments on this solution.

Post comments, submit alternative solutions or receive notifications



Jump to page: [1]

Post a new question about the Canon PIXMA IP1800
All problems on this page have been submitted and answered by users. If you have a problem with the Canon PIXMA IP1800, please submit it below and we'll post it here.

Details of your problem:
Please ensure that the above box is not empty


Please note that all problems are moderated.



  Back to top
Solve an unsolved problem for the Canon PIXMA IP1800

Can you help?
If you can solve a currently unsolved problem, please select the problem you can solve from the list below.
Even if you can't solve it, you can still comment on problems if you think it would help.



Jump to page: [1] [2]
0 people also had this problem.

Problem: IMm using canon ip1980, my black ink tank is full while my colour ink tank is low.. i have the set the printer to print using black colouer only.. but a message appears as the ink cartridge is not recognised (indicating colour ink)

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: Not all lines print. There is white space where text should be--almost as if the printer is skipping.

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: the ink absorber is full. do not print

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: Canon iP1800 'paper jam' but I think that it isn't moving the paper forward onto the rollers?

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: After I turn the printer on, the cartridge tries to move but I don't know what blocks the tray form moving and I get a paper jam error even though there's no paper loaded.

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: B200 error on lcd screen

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



1 person also had this problem.

Problem: i refill cartridge and the error messege occure "it does not installed properly the ink cartridge please open the cover and reinstall the cartridge"

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: photos are orange in color

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: there're some missing column (blank white) when i printed anything. i used to nozzle clean and deep clean several times, but it still doesn't work.please help me..

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



0 people also had this problem.

Problem: every time i replace ink it still says ink running low

There are 0 comments on this problem.

Post solution, add your comments or receive notifications



Actions - No registration required
Find a Printer
Brother
Canon
Dell
Epson
Fujitsu
HP
Kodak
Konica Minolta
Kyocera
Lexmark
OKI
Pandigital
Polaroid
Ricoh
Samsung
Tally
Xerox